Pagina 1 van 3

Cupra R lip draadje

Geplaatst: do dec 03, 2009 6:51 pm
door frank de jonge
This is a nice and subtle addition to any R25/ZR and many other cars.
Good thing about the splitter is it fits many cars as it it flexible and easy to bend, made of plastic so you it can take some bumps and not break and best of all it only costs a tad over £20 to buy from a Seat dealership!

What you need to fit the splitter onto your car is:
- a Seat Leon Cupra R splitter available from Seat dealers (part number is 1ML805903 iirc)

-some self tapper screws (the ones with a sharp tip on them for people who don't know)

Afbeelding

Now there are 2 ways to do this.
you can either -
*Jack up the car and screw it in
OR
*Take the bumper off, drill some pilot holes and then screw it in

or even better, if you can get it on a set off ramps or can lift the front of the car hight enough to drill some holes in, it would make things much easier!


1- This is what the splitter should look like

Afbeelding

2 - Cut down the 2 fins in the middle so the middle section of the splitter doesn't bulge out. (just below half is enough). Offer the splitter onto the car (get a mate to help you), if the middle is still sitting higher then the sides, trim the middle fins a little more

Afbeelding

3 - Re-try a test fit again and if your happy with it, starting from the centre, pilot drill and screw it in. the splitter will have sum tabs on the end of it, drill the pilot holes and screw into that. As you work your way outwards from the centre you will have to bend the spoiler to fit the ZR contour

Afbeelding

4 - You can have the splitter attached in 2 different ways, all the way around the edges or just tucked inside (see pictures below)

Afbeelding

Afbeelding

5 - How ever you attached the splitter, the ends will still be too long, just trim them with a hacksaw.

Job Done! stand back and admire!


Afbeelding

Afbeelding

Voila!

Geplaatst: do dec 03, 2009 7:14 pm
door type3
link werkt niet, je moet je registreren om de link te kunnen bekijken

Geplaatst: do dec 03, 2009 8:42 pm
door frank de jonge
Hmmmz, kopieer alles wel ff hiernaartoe in mn opening *edit, done*

Hier nog een foto van mijn MG ZR met die lip.

Afbeelding

Afbeelding

Geplaatst: do dec 03, 2009 9:28 pm
door p@p@zs
Die rode ZR kijkt wel venijnig :D
Mooi!

Geplaatst: do dec 03, 2009 11:01 pm
door type3
Ik kan je als tip geven dat als je auto echt laag hangt, de parker schroeven niet genoeg zijn, Ik heb mijn lip met een stuk of 20 M6 boutjes vastgehangen, met de parkerschroeven heeft het gehouden tot ik een keer in hog gras reed, vanaf toen heeft mijn lip een paar keer op de grond gehangen (ondertussen ook al aan de 2e toe)
Voor de geintresseerden de bestelnummer bij seat: 1ML805903, kost ongeveer 28€

Geplaatst: do dec 03, 2009 11:02 pm
door Rvelleko
Wat kosten ze ongeveer ?

Geplaatst: do dec 03, 2009 11:03 pm
door type3
prijs erbij gezet

Geplaatst: do dec 03, 2009 11:06 pm
door Rvelleko
:beuh: Waar dan ? bedoel je die 20 Pond ? wat kosten ze in NL ?

Geplaatst: do dec 03, 2009 11:07 pm
door frank de jonge
Om precies te zijn, €34,03 :)

Geplaatst: do dec 03, 2009 11:11 pm
door Rvelleko
Keej dan :mrgreen:

Geplaatst: vr dec 04, 2009 3:45 pm
door type3
frank de jonge schreef:Om precies te zijn, €34,03 :)
Dan zijn ze in nederland duurder als ik belgie, Ik heb mijn eerste +-28€ betaald en de 2é heb ik personeelskoring op gehad en die kostte 20,16€

Geplaatst: vr dec 04, 2009 4:32 pm
door frank de jonge
Zou best eens kunnen.
Kheb em bij de dealer uit Emmen.

Geplaatst: vr dec 04, 2009 8:11 pm
door BarryBrm
Of onder de R200
AfbeeldingAfbeelding

Geplaatst: za dec 19, 2009 12:07 am
door mgzr105lemans
ik denk dat ik ook maar zo,n onderlip er onder doe staat wel gaaf onder een rover of mg zr :)

Geplaatst: za dec 19, 2009 3:10 pm
door mgkevin
type3 schreef:prijs erbij gezet
hey dit lipje van waar heb jij dit toen gehaald ? en plooit dit lipje mee of scheurt deze onmiddelijk als die over de grond schuurt ?

Geplaatst: za dec 19, 2009 4:06 pm
door mgzr105lemans
Hij heeft hem bij een seat dealer gehaald in emmen ik weet niet of het schuurt en of het dik materiaal is